{"id":10394,"date":"2020-10-17T04:48:51","date_gmt":"2020-10-17T11:48:51","guid":{"rendered":"http:\/\/exhaustnotes.us\/blog\/?p=10394"},"modified":"2020-10-17T06:47:47","modified_gmt":"2020-10-17T13:47:47","slug":"the-star-powder-dispenser","status":"publish","type":"post","link":"https:\/\/exhaustnotes.us\/blog\/index.php\/2020\/10\/17\/the-star-powder-dispenser\/","title":{"rendered":"The Star Powder Dispenser"},"content":{"rendered":"

I’m going at the Star resurrection slowly, methodically, and piecemeal.\u00a0 I suppose I could completely disassemble the thing, clean, degrease, and polish all the bits and pieces, and then reassemble it all.\u00a0 But I’m a little bit scared I might not remember how it all goes back together, and I don’t want to spread everything out and make my workbench unusable during this resurrection.\u00a0 Nope, slow and easy is the path forward for me. I’m doing it one bite at a time and I am enjoying the meal.<\/p>\n

The Star Powder Dispenser<\/h2>\n

The first bite is the powder dispenser.\u00a0 It’s the deal that automatically dispenses the right amount of propellant each time the Star’s lever is pulled.\u00a0 It consists of a powder hopper subassembly (the upper arrow)\u00a0 and the dispensing mechanism (the lower arrow), as you see in the photo below.<\/p>\n

\"\"<\/p>\n

Here’s another photo of the dispensing mechanism.\u00a0 It mounts to the Star’s upper plate (Star calls this upper plate the tool head).<\/p>\n

\"\"<\/p>\n

Powder Dispenser Disassembly<\/h2>\n

Here’s the bottom of the powder hopper.\u00a0 It’s brass and it mounts by threading into the powder dispensing subassembly.\u00a0 The silo that holds the powder is plastic, and I think when it was new the plastic was probably clear.\u00a0 It’s occluded with age.\u00a0 That’s okay.\u00a0 So have I.<\/p>\n

\"\"<\/p>\n

This is the powder dispensing mechanism with the powder hopper removed.<\/p>\n

\"\"<\/p>\n

Looking inside the powder dispensing mechanism, there were still a few grains of powder left inside from the last time this reloading equipment was used.\u00a0 I’m guessing that was quite a while ago. My Nikon<\/a>\"\" camera and Sigma<\/a>\"\" macro lens do\u00a0 a wonderful job for this kind of photography.<\/p>\n

\"\"<\/p>\n

Incidentally, speaking of the last time this device was used…several of our readers suggested that the number etched onto the Star reloader’s base was a social security number.\u00a0 Before identity theft became the problem it is today, it was common for folks to etch their social security number on things to prevent theft.\u00a0 One of our blog readers located the man whose social security number was located on this Star reloader.\u00a0 That owner was born in 1926 and died in 2009.\u00a0 \u00a0To my surprise, there’s a social security death index where you can find this information.\u00a0 Who knew?<\/p>\n

Back to the job at hand: The powder dispensing mechanism is secured to the tool head with two slotted screws.\u00a0 I had applied a bit of Kroil<\/a>\"\" to these screws a day earlier and they unscrewed easily.\u00a0 Kroil<\/a>\"\" is good stuff.<\/p>\n

\"\"<\/p>\n

With the two screws removed, the photo below shows what the powder dispenser mechanism looked like.\u00a0 There’s a lower housing, an upper cover, a spring, the two attach screws, and the powder slide.\u00a0 It was all pretty funky when I disassembled it, but I took care of that.<\/p>\n

\"\"<\/p>\n

The powder slide is what actually meters (determines the amount) of powder dropped into each cartridge.\u00a0 When the tool head is up (before you actuate the lever), powder drops into a cavity in the slide.\u00a0 \u00a0When the tool head is lowered (when you actuate the lever), the powder slide is pushed to the left, the cavity containing the powder moves over the powder spout, and the powder drops through the spout into the cartridge case.<\/p>\n

Cleaning Things Up<\/h2>\n

The tube sticking up through the tool head in the photo below is the powder spout.\u00a0 It’s what the left arrow points to.\u00a0 The right arrow points to the bullet seating and crimping die.\u00a0 There was a lot of crud on the die.<\/p>\n

\"\"<\/p>\n

The spout was funky, so I ran a patch through it with a cleaning rod.<\/p>\n

\"\"<\/p>\n

The bullet seating and crimping die is the last of the three reloading dies.\u00a0 It was super funky.\u00a0 It’s the die that seat the bullet and crimps the cartridge case.<\/p>\n

\"\"<\/p>\n

Here’s the “after” photo.\u00a0 I went to work on the die with WD 40<\/a>\"\" and a toothbrush.<\/p>\n

\"\"<\/p>\n

This is the powder dispenser lower housing.\u00a0 It’s funky, too, but just wait.<\/p>\n

\"\"<\/p>\n

The photo below shows the powder slide, and it says exactly what I hoped it would say.\u00a0 Note the “BE” on the upper tine, and the “2.7 GR” on the lower tine.\u00a0 That means this powder slide is designed to throw 2.7 grains of Bullseye powder, and that’s a good thing.\u00a0 That powder and that charge, along with a 148-grain lead wadcutter bullet, is the accuracy load in .38 Special.\u00a0 I got lucky; this is exactly what I wanted to see.\u00a0 Note the two rollers between the tines.\u00a0 I’ll explain what they do a little further along in this blog.\u00a0 And yeah, I know, this is another funky piece.\u00a0 But wait; you’ll see.<\/p>\n

\"\"<\/p>\n

More funkiness…the powder dispensing mechanism cover.<\/p>\n

\"\"<\/p>\n

Here’s another shot of the powder slide and its spring.\u00a0 This is the “before” picture.\u00a0 And that hole in the center?\u00a0 It’s the feature that determines how much powder goes into each cartridge.\u00a0 If you want a different charge on a Star reloader, you need to buy a different power slide.\u00a0 \u00a0Like I said, I got lucky.\u00a0 This one was set up for 2.7 grains of Bullseye.\u00a0 It’s just what I wanted.<\/p>\n

\"\"<\/p>\n

I wiped the powder slide off and, being that it was brass, I wanted to get rid of all the oxidation and then polish it.\u00a0 I was thinking it would be cool if I had some Brasso<\/a>\"\", but since I’m no longer in the Army I don’t have any.\u00a0 Then I remembered:\u00a0 I have Dillon<\/a>\"\" Rapid Polish brass polish that I use with my Franklin Arsenal<\/a>\"\" brass tumbler, and it does the same thing.\u00a0 I put a little on a rag and used it to polish the powder slide.<\/p>\n

\"\"<\/p>\n

Here’s another shot (the “after” photo) of the powder slide.<\/p>\n

\"\"<\/p>\n

Note the rollers on the left end of the powder slide.\u00a0 This thing is like a Ducati:\u00a0 It has desmodromic valve actuation.\u00a0 \u00a0I’ll explain that a little bit further down.<\/p>\n

Next up would be the powder dispenser mounting screws.\u00a0 I went to work on them with a Scotchbrite<\/a>\"\" pad and they cleaned up nicely.<\/p>\n

\"\"<\/p>\n

Here’s the powder dispenser base and the powder on the tool head.<\/p>\n

\"\"<\/p>\n

And here’s the powder dispenser cover, the spring, and the mounting screws reassembled.\u00a0 I used a Scotchbrite<\/a>\"\" pad to clean up the powder dispenser housing and powder dispenser cover, too.\u00a0 They look good.<\/p>\n

\"\"<\/p>\n

And finally, here’s the powder hopper reinstalled on the powder dispenser.<\/p>\n

\"\"<\/p>\n

Desmo Dispenser Actuation<\/h2>\n

You might be wondering how the powder dispenser works.\u00a0 It’s really quite clever.\u00a0 When the Star reloader lever is actuated, the tool head moves up and down on the main shaft, bringing the powder dispenser with it.\u00a0 As that occurs, the powder slide translates back and forth as it moves along the curved cam you see in the photo below.<\/p>\n

\"\"<\/p>\n

Remember those two rollers in the powder slide?<\/p>\n

\"\"<\/p>\n

They follow the vertical cam path shown two photos up.\u00a0 The inner roller rolls along the cam as the tool head moves down, and the outer roller rolls along the cam as the tool head is returned to the up position.\u00a0 This is desmodromic actuation, just like Ducati uses on the their motorcycle intake and exhaust valves.\u00a0 They’re driven open by a cam, and they’re driven closed by a cam.\u00a0 Star could have just used pins instead of rollers, but they went with rollers (a more expensive and more reliable approach, I think).\u00a0 When the tool head moves down, the powder slide takes 2.7 grains of Bullseye powder, shifts it over the powder spout, and gravity does the rest.\u00a0 Take a look.<\/p>\n