{"id":1423,"date":"2018-10-27T20:45:54","date_gmt":"2018-10-27T20:45:54","guid":{"rendered":"http:\/\/exhaustnotes.us\/blog\/?p=1423"},"modified":"2019-02-02T10:05:38","modified_gmt":"2019-02-02T18:05:38","slug":"zeds-not-dead-part-6","status":"publish","type":"post","link":"https:\/\/exhaustnotes.us\/blog\/index.php\/2018\/10\/27\/zeds-not-dead-part-6\/","title":{"rendered":"Zed\u2019s Not Dead: Part 6"},"content":{"rendered":"

\"\"I\u2019ve been spending some time with Zed\u2019s carburetors, working on details that required home-brewed engineering. The Mikuni carbs on Zed don\u2019t have a traditional choke (a flap that blocks air going into the carb causing a rich mixture) but we still call it a choke. Instead, Zed\u2019s carbs employ an enrichener circuit, which is more like a tiny, completely separate carburetor grafted onto the main body of the carb. Sort of like the brain inside Krang\u2019s stomach on the Teenage Mutant Ninja Turtles cartoon. The enrichener has its own air intake on the upwind side of the throttle slide. This fuel circuit is fixed; no adjustment needed and is controlled by a plunger on the downwind side of the throttle slide. Lifting the plunger allows air to flow through the tiny carburetor at a pre-set fuel\/air mixture and if everything else is right, helps a cold Kawasaki engine start better.<\/p>\n

One of Zed\u2019s four carbs was missing the little plastic bobbin that slides over the enrichener plunger shaft and is held onto the shaft by a tiny Jesus Clip. Two small fingers connected to the choke rail act on this bobbin and without it the plunger won\u2019t lift. I Googled for a bit but could not find the bobbin part so I attempted to make one. I drilled a plunger-rod sized hole through a small piece of nylon and chucked the nylon into a Ryobi drill. Using a flat file I machined the nylon as the drill motor spun: a New Mexican hand-lathe. It worked great until the center of the bobbin got too thin and the whole mess spun out of control leaving me with a distorted pile of junk.<\/p>\n

\"\"Back to square one. I noticed how the bobbin was nearly the same size as the pop rivets I\u2019d been using to assemble parts of Tinfiny\u2019s generator room. I have about 500 of these rivets in stock so I could afford to lose a few. Knocking the pin out of the pop rivet revealed a bore just a wee bit small for the plunger shaft but it was not a problem to run a drill bit through making the bore an exact fit for the plunger. A pop rivet only has one flanged side so I repeated the process on a second rivet, cut the two rivets to equal the length of a factory bobbin and assembled the mess. I cannot wait for a hard-core Z1 enthusiast to happen upon the aluminum bobbin. It\u2019ll probably cause a heart attack as most Z1 fans are around 75 years old.<\/p>\n

\"\"Between the throttle linkage pivots on each set of two carbs there are little dust covers made from a treated black paper. Or maybe the dust covers are rubber, I can\u2019t tell. Three of the four covers were broken on Zed. The covers go over the springs and ball joints on the linkage. They don\u2019t seal all that well but might keep a larger bug from crawling in there.<\/p>\n

\"\"This is a part I didn\u2019t bother looking for because I can make new ones in less time than it takes to look them up and order them. I used the thin plastic lid from a box of self-tapping sheet metal screws. Without a lid you know the screws are going to end up scattered across the shed floor. The dust covers didn\u2019t come out as nice as I would have liked. Luckily, once installed you can\u2019t see the things.<\/p>\n

\"\"On the Z1 900cc, each set of two carbs share a fuel inlet pipe. The pipe goes between the carbs and is a metal Tee fitting with thick rubber o-rings cast onto the straight section of the Tee. This rubber hardens and shrinks resulting in a loose, leaky fit. You can buy new ones for 34 dollars but if you\u2019ve read Zed\u2019s Not Dead this far you know what is going to happen next.<\/p>\n

\"\"I cut the rubber away from the fuel pipe and polished the exposed metal to ensure a smooth sealing surface. Then I drilled a small hole near the end of the pipe in order to install a pin (made from the drill bit). The pin is the same length as the width of the fuel inlet bore so once it is installed in the carb body the pin can\u2019t fall out.<\/p>\n

\"\"Now I used a \u00bc-inch length of rubber fuel hose (be sure to use the non-reinforced hose as cloth reinforcing strands will wick fuel, causing a leak) and slid this hose onto the fuel Tee. Next came washers and finally the pin. The assembly fits snugly into the carburetors. It helps to put the fuel feed hose on before you slide the carbs together. Hopefully it won\u2019t leak.<\/p>\n

\"\"I\u2019ve got the carbs assembled onto the rack and everything seems to work smoothly. I\u2019ll be testing the float levels on the bench and will sync the throttle slides as close as I can get them. The idea being all four slides move the same distance in unison. Even if they\u2019re not perfect the bike should run reasonably well. Later, manifold vacuum gauges can be used to adjust the carbs for any slight differences between cylinders.<\/p>\n

\n

Want to follow the entire Z1 resurrection?\u00a0 Just click here<\/a>!<\/p>\n","protected":false},"excerpt":{"rendered":"

I\u2019ve been spending some time with Zed\u2019s carburetors, working on details that required home-brewed engineering. The Mikuni carbs on Zed don\u2019t have a traditional choke (a flap that blocks air going into the carb causing a rich mixture) but we still call it a choke. Instead, Zed\u2019s carbs employ an enrichener circuit, which is more … Continue reading “Zed\u2019s Not Dead: Part 6”<\/span><\/a><\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"jetpack_post_was_ever_published":false,"_jetpack_newsletter_access":"","_jetpack_dont_email_post_to_subs":true,"_jetpack_newsletter_tier_id":0,"_jetpack_memberships_contains_paywalled_content":false,"_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[235,96,66],"tags":[329,379],"class_list":["post-1423","post","type-post","status-publish","format-standard","hentry","category-amazon","category-feel-good-stuff","category-joe-gresh","tag-kawasaki-z1","tag-kawasaki-z900"],"jetpack_featured_media_url":"","jetpack_sharing_enabled":true,"post_mailing_queue_ids":[],"_links":{"self":[{"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/posts\/1423","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/comments?post=1423"}],"version-history":[{"count":6,"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/posts\/1423\/revisions"}],"predecessor-version":[{"id":2546,"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/posts\/1423\/revisions\/2546"}],"wp:attachment":[{"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/media?parent=1423"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/categories?post=1423"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/exhaustnotes.us\/blog\/index.php\/wp-json\/wp\/v2\/tags?post=1423"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}