{"id":33378,"date":"2026-05-27T00:01:40","date_gmt":"2026-05-27T07:01:40","guid":{"rendered":"https:\/\/exhaustnotes.us\/blog\/?p=33378"},"modified":"2026-05-14T12:42:24","modified_gmt":"2026-05-14T19:42:24","slug":"harrison-design-python-front-sight","status":"publish","type":"post","link":"https:\/\/exhaustnotes.us\/blog\/index.php\/2026\/05\/27\/harrison-design-python-front-sight\/","title":{"rendered":"Harrison Design Python Front Sight"},"content":{"rendered":"
By Joe Berk<\/h6>\n

I am enjoying my Colt Python more and more every time I shoot it.\u00a0 The latest improvement is the Harrison Design front sight, as seen in the photo above.\u00a0 Just prior to installing it, I had installed the Wilson Combat rear sight, as seen in the photo below. I covered the Wilson Combat rear sight in my previous blog.<\/p>\n

\"\"
The Wilson Combat Python rear sight. It’s much sturdier than the stock rear sight.<\/figcaption><\/figure>\n

The Wilson Combat rear sight is a solidly built affair, but it sits higher than the stock Python rear sight.\u00a0 That caused my shots to hit high.<\/p>\n

\"\"
Typical targets fired with the Wilson Combat rear sight.\u00a0 These targets were shot at 15 yards, or 45 feet.<\/figcaption><\/figure>\n

I needed a taller front sight to work with the Wilson Combat rear sight.\u00a0 I researched this issue, and apparently I was not alone.\u00a0 Numerous comments appear on various forums identifying the Python shooting high issue with the Wilson Combat rear sight.\u00a0 Harrison Design did something to address it:\u00a0 They offer taller Python front sights.<\/p>\n

Turning to my junior high school geometry, I calculated the required front sight height based on where my shots were hitting, and the following formula:\"\"<\/p>\n

The stock Python front sight height is 0.180 inches, the distance to the target is 45 feet, and the distance from the front sight to the rear sight (the sight radius) is 7.875 inches.\u00a0 Plugging those values into an Excel table based on the above formula, I found the front sight height increase I needed.<\/p>\n

\"\"<\/p>\n

To go up 2.88 inches at 45 feet, I needed a 0.042-inch taller front sight (the front sight would have to be 0.222 inches high, which is obtained by adding the 0.042-inch additional required front sight height to the stock 0.180-inch stock front sight height).\u00a0 Harrison Design<\/a> offers taller Python front sight heights of 0.200 inches and 0.230 inches.\u00a0 I chose the 0.230 Harrison Design front sight, as it was closer to the calculated front sight height I needed.\u00a0 I knew I could account for the small difference between the calculated required front sight height increase by simply raising the rear sight.<\/p>\n

\"\"
Colt Python stock front sight (left) and the replacement taller Harrison Design front sight. I prefer a plain black front sight as it makes for a clearer sight picture.<\/figcaption><\/figure>\n

I opted for a plain post front sight, as seen in the above photo on the right.\u00a0 Harrison Design<\/a> offers high visibility front sights (ones with a translucent plastic cord within the sight), gold dot front sights, and perhaps others.\u00a0 For precision work, I’m old school.\u00a0 I greatly prefer a plain post.\u00a0 For me, it’s harder to focus on the top of a red ramp (like the original Colt front sight, shown on the left) or on a gold dot front sight.\u00a0 \u00a0The gold dots have another issue for me:\u00a0 My point of impact on the target moves around when the lighting changes.\u00a0 I’m not a fan of “gee whiz” front sights.\u00a0 I learned from a master (Sergeant Major Emory Hickman) and I learned on a plain black post front sight.\u00a0 Your mileage may vary.<\/p>\n

Harrison Design does a nice job in what they include.\u00a0 In addition to the taller front sight, they provided a separate set screw (not necessary, as I could reuse the original one), a tiny Allen wrench for the set screw (also not necessary, as I already had one), and a set of installation instructions\u00a0 (not necessary for me, as how it all goes together is obvious).\u00a0 But I thought it was nice Harrison Design included all these things.\u00a0 The new front sight slipped right into place.\u00a0 Replacing the original Colt front sight with the taller Harrison Design front sight took less than a minute.<\/p>\n

So how did it all work on the range?\u00a0 Pretty much just like the numbers said it should.<\/p>\n

\"\"
A 50-foot target shot with the new Harrison Design front sight and the Wilson Combat rear sight. Point of aim was at 6:00 on the orange bullseye.\u00a0 The load I used for this target was Missouri Bullets’ 180-grain truncated roundnose cast bullet and 14.0 grains of IMR 4227 (a max load).<\/figcaption><\/figure>\n
\"\"
Same as above, but with 148-grain wadcutter, 2.7-grains of Bullseye target loads, fired at 50 feet.<\/figcaption><\/figure>\n
\"\"
A “first look” type of target at 25 yards. The load was Missouri Bullets’ 180-grain truncated roundnose cast bullet and 14.0 grains of IMR 4227 (a max load).\u00a0 There’s a little more spread than I find acceptable, but I attribute that to bullet casting defects I’ll cover in a subsequent blog.<\/figcaption><\/figure>\n

The bottom line is I am a satisfied customer.\u00a0 Harrison Design makes a good product.<\/p>\n

Coming up?\u00a0 I’m going to run another set of Python tests assessing cast bullet base imperfections and their effect on accuracy, and then yet another assessing accuracy at 25, 50, and 100 yards.\u00a0 Then I’m going pig hunting with the Python.<\/p>\n

Stay tuned.<\/p>\n

\n

Subscribe to ExNotes for free!<\/strong><\/p>\n