The Husqvarna 510 SMR came stock with a 35-watt/35-watt incandescent headlight bulb that was nearly useless. I say nearly because when it was lit it provided a weak beam limiting nighttime speeds to 30 miles per hour. But it was worse than that because for some reason the motorcycle constantly blew the bulb leaving me to get home using the little parking light bulb (which never blows out). The plastic headlight fixture shows signs of melting even with the standard bulb so I set about trying to find a better idea.
Husky uses an S-type light socket base like you’ll find in scooters and mopeds. This bulb was used as my baseline for temperature and current draw. I figured if I didn’t exceed the standard bulb on these two measurements the plastic headlight should survive and the electrical system would be able to keep up with the program. Baseline was 2.5 amps @ 13-volts and 230 degrees. I did all the tests using highbeam.
The stock incandescent light surprised me. It’s the oldest technology, they’ve been around more than a hundred years, yet it wasn’t the worst of the bunch. I had to try and find something better, though.
I bought the LED bulb off of Ebay and I have no ratings on it because I can’t find it for sale again. The bulb has no markings. It was like a one-shot deal I guess. The reason I chose this one was that unlike the other LEDs it didn’t have the large heat sink or cooling fan behind the bulb. It was a direct fit for the Husky’s push-and-twist bulb socket. The LED used so little power I had to check a few times to believe it. Only 0.14 amps were required to fire the thing up! It also ran much cooler than the other bulbs, producing only 134 degrees. I’m thrifty so I loved the thing but there’s a reason those other LED bulbs have such a big big cooling system: The light output from the minimalist LED was weaker than the stock bulb by a lot.
The halogen was a 50-watt high and low beam. I tried to find a 35-watt halogen but couldn’t at the time. I’ve since found a 35-watt and I’m going to get one and try it. As you would expect, the higher wattage bulb drew more current and ran much hotter: 4.9 amps and 337 degrees (still rising fast). I stopped the test early because I didn’t want to melt my headlight shell. The Halogen was very bright and did a great job projecting all that power to the front. It was the brightest bulb by far. I’d love to be able to run the halogen but I think I’ll have a meltdown if I do.
I found a HID bulb-ballast combination with a multi-fit base that would fit in the Husky’s socket but I would have to gut the contacts to allow the harness passage through. I didn’t want to do this so I just held the bulb in the reflector housing. It was a disappointing bulb consuming more power and putting out less light than the incandescent bulb. If you’ve ever had one of those adjustable, wide/narrow beam flashlights you know how little it takes to change the beam pattern. Bulb position is critical for good output and the HID must not have been in alignment with the reflector’s focal point.
In the video link you’ll see the four bulbs I tested and the statistics on each one. All the bulbs had their pros and cons but none of them solved the problem. I ended up using the LED even though the bulb was the weakest. I was going on a trip to Utah and wanted to see if it would stay together longer than the incandescent. It is still going after 2400 miles. The stocker never lasted as long.
I think I will have to replace the entire headlamp on the Husky to get a decent light. The plastic construction limits how much wattage I can use and is borderline melting at stock levels of heat. I don’t ride much at night but sometimes you get caught out and have to muddle through. I added a bright off-road light to the Husqvarna just for those situations.
Sign up here for automatic email notifications:
Like this blog? Want to have a page with links to Joe Gresh’s product reviews? Have other suggestions? Let us know in the Comments section!
