Revolver – The ExhaustNotes Blog

Whole lotta end shakin’ going on…

I love my S&W Model 60 and I shoot it a lot. It’s particularly cool after I had TJ (of TJ’s Custom Gunworks) do an action job on it. Not content to leave well enough alone, I convinced myself that (after tracing the occasional double action misfire to not-fully-seated primers) that what I really needed was a lighter hammer spring (in addition to the lighter trigger spring I had already installed). Wolff Springs sells a lighter hammer spring kit, and I went for the lightest hammer spring I could get.

The Wolff Springs hammer spring kit. I went with the lightest spring.

The lighter trigger spring affects single action trigger pull after you have already cocked the gun and it has nothing to do with the occasional double action misfiring I had experienced in the past. Double action trigger pull is affected by both the trigger spring and the hammer spring, but the hammer spring is a much beefier spring and it drives most of the resistance when firing double action. The hammer spring, if too light, can induce misfires.

The Wolff hammer spring kit includes a standard strength spring (an 8 1/2-pound spring), a heavier spring (a 9-pound spring), and a lighter spring (an 8-pound spring). I wanted a lighter double action pull, so I used the 8-pound spring. The tradeoff is this puts less force on the hammer, which means it has lower velocity when it hits home, and that ups the likelihood of a misfire.

The hammer spring is easy to change, and if necessary, I can go for either of the two heavier springs at the range. All it takes is a small screwdriver to remove the grips, and the same exotic custom tool used for disassembling the Rock Island Compact 1911 (a bent paper clip). The photos below show how this is done.

The Model 60’s hammer spring, with the hammer in the uncocked position.

The Model 60’s hammer spring, with the hammer cocked. Note that the hammer yoke (the rod running through the center of the hammer spring) has been pushed back, exposing a hole in the rod.

A high tech, German tool steel special assembly/disassembly aid? Nah, it’s a bent paper clip and it works gang busters.

To remove the hammer spring yoke and the hammer spring, insert the paper clip into the yoke and gently release the hammer by pulling the trigger and lowering the hammer.

With the hammer dropped, the spring is captured in a compressed mode and the hammer spring and the yoke can be removed from the gun. Once this subassembly is removed, you can manually push the spring cap to further compress the spring, remove the paper clip, remove the spring cap and spring, and install the lighter hammer spring. Assembly is the reverse of disassembly.

While installing the new hammer spring, I noticed that my normal gun cleaning routine just wasn’t cutting it on the Model 60. There was still a bit of lead in the barrel, and the powder residue was building up around the yoke. I selected a bronze bristled toothbrush and went to work on the cylinder, the yoke, and the frame, and a bronze bore bush for the bore. When the remnants of gunfights past were gone (you know, my encounters with zombies, as previously described), I spritzed the gun with the universal cleaner (WD40) and then I wiped it down before applying gun oil.

That’s when I noticed that the barrel-to-cylinder gap was nonexistent. Zip. Nada. Zero. The front of the cylinder was touching the rear of the barrel. Uh oh. That’s no good. There’s supposed to be a gap there (like you see in the photo below), because if there’s no gap the cylinder will drag on the barrel. That will degrade the double action trigger pull and, in a worst-case scenario, it can drive the revolver out of time (the chamber won’t be aligned with the barrel). The technical term for the fore-and-aft cylinder movement that assures a minimum clearance when the cylinder is fully forward is called end shake. There needs to be some, and there needs to be a gap. Ideally, that should be 0.004 to 0.008 inches. Any less, and powder and lead residue will bind the cylinder, any more and too much gas escapes (and velocity suffers).

The barrel-to-cylinder gap. This is about .004-inch with the cylinder pushed forward, and that’s the gap I want. This was after I installed the TriggerShims.com cylinder shim.

You measure the barrel-to-cylinder gap with a feeler gage, just like you would when setting the valves on a motorcycle. I’ve done that (as you know from reading this blog and any of the CSC shop manuals), and I already had the feeler gages I needed.

My feeler gage. I’ve probably owned this tool for 40 years. It still works. I use it for adjusting valves on my Royal Enfield, too.

After a bit of internet research, I learned that the way to address inadequate gap is by shimming the cylinder and its fit on the yoke. That’s when I first learned there’s a business that specializes in making shims for this exact purpose. In short order I was communicating with Lance Shively, who heads TriggerShims.com.

The cylinder shims from TriggerShims.com. They were well packaged and sent in a standard business envelope.

The cylinder shims out of the pack. I ordered the four-piece set because I had not worked with these before, I didn’t know what I would need, and they were inexpensive. They are color coded by size.

Lance and his wife, Tammy, run a real Mom and Pop operation that manufactures gun specific shims for a living. Lance has an extensive background in small engine repair and tool and die making, and he and Tammy parlayed that into TriggerShims, which has been doing well for more than 14 years now. Lance told me his primary concern is customer satisfaction, and I can tell you my perception in working with TriggerShims is they have mastered it. I had the Model 60 custom end shake shims in three days, there was no postage charge, and the price was more than reasonable for custom gun parts. Lance runs a Christian business, he believes in God and country, and he’s not bashful about letting people know that. He and Tammy also sell select items from other vendors when he finds a company he likes and believes in, but that is a very select group. The two biggest ones are Wolff and Volquartsen.

I received the shims I ordered from Lance in just a few days, and installation was trivially easy. I had to remove the yoke, disassemble the ejector rod from the extractor, install the shim I wanted to use (I went with a single .003-inch shim to give the clearance I wanted), and then reassemble everything. It only took a few minutes, and the only tricky part was remembering that the ejector rod had a left-hand thread.

This screw has to be removed to allow removal of the yoke and cylinder from the revolver. You don’t need to remove the revolver’s side plate.

With the yoke removed, you unscrew the ejector rod (the knurled piece you push on to eject empty brass from the cylinder) and everything comes apart. Hold on to the ejector rod as you unscrew it so parts won’t fly away, and remember that it is a left-hand thread.

The cylinder shim(s) fit beneath the extractor spring. They are pushed into the cylinder by the extractor spring as the cylinder and yoke subassembly are reassembled. The shim(s) position the cylinder further to the rear, increasing the barrel-to-cylinder gap.

TriggerShims.com manufactures over 100 firearm-specific shims with thicknesses from .002-inch to .007-inch, with some specialty items as thick as .010-inch and as thin as .0015-inch. Lance sends shims worldwide, with Australia and Canada being the biggest international customers (he also ships to more than 100 other countries).

Lance and I had a good conversation, during which he told me he enjoyed exploring the ExhaustNotes site and our blog. One thing led to another, and TriggerShims.com is our newest advertiser. You’ll see the TriggerShims.com logo on the ExNotes blog and all ExNotes pages, and Lance asked if he could post links to some of our Tales of the Gun stories on the TriggerShims.com site. Hey, you bet, Lance, and welcome aboard.

I had the Model 60 on the range yesterday morning, and it is a much smoother running revolver. I confirmed another issue I’ve experienced on this revolver before, and that’s a slightly out-of-time situation when firing double action (probably induced by the cylinder drag described above). That’s going to take a new hand to correct (“hand” is the nomenclature used for the part that advances the cylinder). The replacement hand is on order, and there will be another Model 60 blog coming up in a couple of weeks on it. As always, stay tuned.

More Tales of the Gun!

Never miss an ExNotes blog…sign up here for free!

Ruger’s Custom Shop Super GP100

Colt has a custom shop, Remington has a custom shop, Winchester had a custom shop, Savage has a custom shop, Springfield Armory has a custom shop, CZ has a custom shop, and Smith and Wesson has a custom shop. It seemed Ruger was the only one of the big players that didn’t have a custom shop.

That’s changed. Ruger recently announced that they, too, now have a custom shop, except they do things differently. Rather than taking orders for custom features on their regular line of firearms, Ruger’s approach is to produce limited numbers of highly-customized guns. Stated differently, Ruger picks the features they want to add to their custom guns; your choice is to purchase it (or not). It’s not a bad way to go.

Note the new Super GP100’s dark PVD finish, the green fiber optic sight, the slotted barrel shroud, and other custom touches.

Ruger’s two most recent custom shop models are revolvers they call the Super GP100; one chambered in 9mm and the other chambered in .357 Magnum. These revolvers have a number of custom features, including a shrouded and vented barrel, 8-shot capacity and the ability to use star clips for speedy reloads, radically-fluted cylinder (I like the look), PVD (that’s physical vapor deposition) finish, polished and slicked up trigger and internal componentry, oversized Hogue hardwood grip, an 11-degree barrel crown (that’s supposed to enhance accuracy), and a fiber-optic front sight (never had one of those before; I’m eager to see if it really does anything for me).

Befitting its custom status, the Ruger Super GP100 comes with a higher-quality carrying case.

The Super GP is offered in two chamberings: .357 Magnum and 9mm Parabellum. The 9mm version is not approved here in the Peoples Republik of Kalifornia. That’s probably okay, as I would go for the .357 if given the choice. But that’s not a choice that’s going to be offered any time soon. Read on, and you’ll see what I mean.

The 9mm version of Ruger’s new Super GP100 revolver. It looks good. Note the shorter cylinder.

I like the way Ruger handled the 9mm Super GP100. The cylinder is shorter to match the 9mm cartridge, and the barrel extends back into the frame. This means the 9mm bullet has less of a jump to the rifling in the barrel, which should improve accuracy. It’s the same thing Smith and Wesson does on its .45 ACP revolvers.

Ruger doesn’t stock these guns. True to the custom shop concept, Ruger builds them as orders are taken. But it wouldn’t do any good to order one now, unless you just want to get a place in line. Due to the press of handgun orders induced by the election, the pandemic, and the recent civil rioting in major US cities, Ruger has its workforce focused elsewhere on meeting the unprecedented demand for its standard guns. As an aside, it’s tough to buy ammo right now, too, for the same reasons. That’s not bothering me, as I reload on my RCBS reloading gear and I’m well stocked.

I’m in the market for a .357 Mag revolver, but I’ll probably go with a more traditional handgun. Maybe a .357 Blackhawk or a S&W Model 27. I’ll keep you posted.

Revolvers, rifles, reloading, and more…check out our Tales of the Gun page!

Book Review: Revolver

My daughter buys books for me, and she has a knack for finding great ones she knows I will enjoy. The latest in a long line of successes is Jim Rasenberger’s Revolver: Sam Colt and the Six-Shooter That Changed America. I enjoyed the book on many levels because I’m a shooter, I like biographies, I’m a student of business success, I like to read about mechanical things, and I love history (especially the history of the American West). Revolver checked all the boxes.

Samuel Colt was anything but an overnight success, but successful he sure was. He was one of the key figures in our Industrial Revolution, and he made the concept of interchangeable parts and mass production work well before Henry Ford came along. Colt started out as sailor on a merchant vessel, he became a huckster selling laughing gas exhibitions, he failed at his first attempt to build a firearms manufacturing business, and then he succeeded wildly when he worked with Samuel Walker, the Texas Ranger who guided Colt’s design of the famous Colt Walker. Revolver delves deeply into all this, including the Colt Walker story, and a grand story it is.

On that topic of the Colt Walker: The Walker was the .44 Magnum of its day, a gun so over-the-top in size and power that as Colonel Colt observed, “it would take a Texan to fire it.” I always thought it would be cool to own a Walker, but Colt only made 1,100 of them, and originals don’t come up for sale too often. The last one that did went for over a million dollars. The blogging business is good, folks, but it ain’t that good.

Robert Duvall as Gus MacCrae in Lonesome Dove, the greatest story ever told (in my opinion). Gus carried a Colt Walker.

Uberti, a company in Italy, manufactures a replica of the original Colt Walker, and reading Revolver gave me the push I needed. I ordered one this morning. Good buddies Paul and Duane are both black powder aficionados, and I figure they can give me the help I’ll need learning how to load and shoot these historical weapons.