Default To No

After I made a particularly snarky Facebook comment regarding some newfangled electronic rider aid, a former editor sent me an email asking why I always slag off electronic controls. He asked if I had ever ridden a motorcycle equipped with traction control, wheelie control, engine power selector toggle or one built after 1971.

Usually my emails run to the “Are you still here?” variety so instead of my stock comeback (“Catterson’s hair is prettier than yours”) I played it straight. The truth is, I haven’t ridden a modern, electronic superbike. But it seems whenever new technology comes along my default mode is “No.” I have a hard time making the junky old motorcycles I habituate ignite fuel, why add complications?

There’s no sense having me ride a modern superbike because it takes skilled crashers…I mean riders to determine if the buffering of the improved, Datacom-7734 chip inside a Yamiguchi ECU has really increased corner exit speeds a hundredth of a second, or perhaps Ducatazzi’s PMS 7724 chip is more like butter?  We’ll never know because I accidently connected the battery backwards and fried the circuit board.

It’s not that I don’t like going fast, it’s just important to me how I get up to speed. I blame my Luddite ways on HO scale slot cars. Long ago, when a steady hail of meteors bombarded the earth, kids raced slot cars. The track was a two-slot, snap-together, plastic roadbed. Plated-metal rails paralleled each slot; these metal rails supplied low-voltage power to the cars via a driver-controlled rheostat.

Underneath the slot car chassis was a guide peg that fit into the track and spring-loaded contact brushes (on Aurora cars) or troublesome foil brushes pivoting on the slot assembly (on the much faster Tyco cars). These brushes conducted the rail power to a tiny electric motor. Untold hours were spent modifying the little motors and experimenting with different brands of tires. My friends and I spent many enjoyable hours racing against each other and the physical limitations of the system.

Since the rails in the track were plated steel, one of our tribe came up with the bright idea of gluing a magnet to the car’s frame to help hold it onto the track. Straight line speed suffered but cornering speed increased dramatically. Overnight, the worst driver of a magnet car could easily beat the best driver of an un-magnetized car. If one magnet was good then two had to be better. Magnets kept going lower until thin sheets of paper were used as a shim to space the magnets as close as possible to the rails.

The cars got faster. Aurora itself cut away the frame and lowered the motor magnets in their vertical-shaft HO cars to take advantage of the steel rails. The final iteration saw a dropped-motor Aurora with huge, front and rear mounted magnets nearly scraping the rails. This car could run upside down if you cared to build an upside down track. Driver skill, once the most important factor in our races, was extinct; all one had to do was hold the rheostat wide open. Soon the rheostat was unnecessary and we hard-wired the track for full power all the time.

The cars were incredibly fast. It was hard to keep them in sight as they blazed around, gripping the track so tightly the plastic corners would shift as they flew through them at top speed. The cars never jumped the slot.

It wasn’t long before we tired of racing and built ramps to jump the cars. From there things devolved into smashing the cars headlong into walls, then to pouring lighter fluid on the Auroras and setting them on fire to see how long they could circuit the track ablaze.

I loved slot car racing but making it foolproof turned it into that detestable thing: boring. In his email, my old editor told me a modern 1000cc sport bike would be nearly unrideable without the electronic aids. I believe him. So far active-electronic motorcycles still require rider skill to pilot at race speeds but the future looks grim. As for me, unless an electronic aid drastically improves my riding experience I’ll keep defaulting to “No.” I love motorcycling too much to risk losing interest.

Zed’s Not Dead: Part 3

There’s never a good time to work on carburetors. I was hoping for a quick rinse out operation on Zed’s fuel system but besides being dirty, sleeping in the rough has corroded Zed’s right-side carb. The other three carbs show less water damage, lessening towards the left side. No doubt due to Zed leaning to the right against The Carriage House (Tinfiny Ranch’s future guest quarters after Metallica, the main house, is finished).

My idealized, simple douche with carb spray has turned into a complete tear down of the 4-carb bank. I haven’t counted but there must be well over 100 parts between the set. Cleaning the white, calcareous deposit liberally coating the inside of the float chamber has kept me occupied and humble.

Certain parts of the carbs are well and truly stuck. The levers that raise the slides are age-welded to the pivot shafts. I gave them a firm shove and I’m not in the mood to break anything right now. The float bowl drain plugs have resisted my better efforts to unscrew them so I’ll be leaving those as is also. One screw has already broken off on the intake port and another one was pre-broken in the ignition area. I’ve got plenty of drilling and bit wrangling to do. I want to get the carbs clean enough to run the engine before destroying them with my ham-fisted efforts to achieve perfection.

Parts for Zed have begun to trickle into Tinfiny Ranch’s high altitude motorcycle shop. I scored four new intake rubbers for $50 off of Ebay, which seemed like a good deal to me. Not such a good Ebay deal was the ignition advancer bolt and grooved washer. I paid $19 and later found the two parts on Z1 Enterprises for $13.

Z1 Enterprises has a lot of Kawasaki Z1 parts for not unreasonable prices. I bought a complete new wiring harness for $139. The harness comes with the main wiring loom, the gauge cluster loom, the rear tail light/blinker loom and the loom underneath the battery box that the regulator, stator, main harness and some other junk I can’t remember plug into.

Also coming from Z1 Enterprises are fork seals, fork dust boots, a right-side handlebar switch and a few gaskets and o-rings. As I’ve yet to receive the stuff I can’t speak to the quality of the parts but I’ll be sure to let you know how it goes.

I’m into Zed’s resurrection for about $240 so far. I’ll be going back to carb cleaning now. The things are a mess and every time they dry out a new, white-powder film appears. I’m using mild solvents so far but I may have to step up my game to get the carbs spic and span. You know the routine; Part 4 to follow.

If you’d like to catch up on the first two “Zed’s Not Dead” installments, here are the links:

Zed’s Not Dead: Part 1

Zed’s Not Dead:  Part 2

Zed’s Not Dead: Part 2

The first thing I wanted to check on Zed was whether the oil was contaminated or if the wet sump Kawasaki engine was full of rainwater from sitting outside. This was not such an easy job as the previous owner had used a chainsaw to tighten the drain bolt. The head of the bolt was mangled into a tapered affair that resisted all vise-grip attempts to get a purchase. Finally I managed to grip the o-ring flange area and got the sad thing out of the oil pan.

Luckily for me the oil came out black, pure and dirty. I priced a drain bolt and while it was a reasonable 15 bucks for a new one I decided that there was plenty of good meat remaining on the old bolt. Using 7 dollars worth of cutting blades on my 4-inch grinder I cut a 14mm hex head into the wreckage and then smoothed the saw cuts with a 9-dollar flap wheel. After I had the bolt looking respectable I ran down to Home Depot (using 1 gallon of gas @ $2.67) and bought some $6.99 silver spray paint. The paint really made the bolt look sweet and I had the satisfaction of saving money to boot!

I have no idea what originally stopped the Zed from running but by the look of the wiring harness it was electrical. The harness is melted in several places and severed in several others. It’s like someone thought they could cut the bike back to health. Cutting is a sign of deeper psychological problems and the fact that the ignition system was in a cardboard box showed how desperate things had become.

Silicone sealant slathered on the weather cracked rubber intake manifolds was less likely to stop the bike. I have found 4 new manifolds on ebay for $50 and they are on the way. Removing the carbs and air box runners was a straightforward operation.

Until this screw broke off, it’s always worse when a screw breaks on the way out. You’ll never have as good a connection as you did when the part was one piece. I am soaking it with PB Blaster, there’s no rush. At least I can get a straight shot at the piece stuck in the head.

I removed the sparkplugs for a quick, finger-in-the-plug-hole compression test and Zed has compression on all four cylinders. The actual PSI number is not too important at this time. I was more worried about a bad valve or holed piston. The sparkplugs were fluffy-sooty and so is the piston (what I can see of it through the plug hole). The bike was running rich or maybe as the ignition died combustion became less of a sure thing.

I’ve got enough apart to have confidence Zed’s engine will run. Hopefully the gearbox will be ok and the stator will charge the battery. In Part 3 we will clean, clean, clean!

Zed’s Not Dead: Part I

I didn’t start out wanting a Kawasaki Z1. I’m more of a H2 750 triple guy. We were renting a house 10 miles south of Alamogordo, New Mexico and my job was to find a place to buy. Land is cheap in New Mexico and I wanted lots of it. 150 acres was the low-end of what I considered a decent spread.

Tinfiny Ranch’s 5 measly acres with a tiny shack was overpriced by about 50% and after checking the place out I told the real estate agent no dice. I did tell him I was interested in the old Kawasaki leaning against the side of the shack. A call was made to the daughter who inherited Tinfiny and a deal was made. Zed was mine.

Zed came with no title, two Emgo café farings (one color-matched!), three seats, a box full of parts, a repair manual and any other bits I could find digging through the little junk-filled storage area next to the bike. Zed’s chain was rusted and the bike was difficult to push. I used a come-a-long to winch the thing up into the truck and hauled the mess back to our rental place.

Then they sold the place we were renting. CT (my wife) found another rental in Tularosa, 10 miles north of Alamogordo and we hauled all the junk we had accumulated, including Zed, to the new joint.

A year had passed since I bought the Kawasaki and the bike was sitting in a storage trailer waiting for motivation on my part. The bike had no title so I wasn’t gung ho about the whole magilla. I mean, it wasn’t an H2, you know?

We were still looking for a place to call our own when the agent who had shown us Tinfiny Ranch called and said the seller was really lowering the price. CT and I went back out and looked the place over again. Tinfiny had electric service (not activated) a water well (broken), a septic system and a horrific wreck of a shack. It was only 15 miles from CT’s work. We figured what it would cost to make Tinfiny into what we wanted and worked our way back to a price. The agent said no way would the daughter take our offer and of course she did. I hauled the Kawasaki right back to where I had originally gotten the bike. Zed was back home.

Buying Tinfiny Ranch turned out to be a good thing because the rental we were living in also sold and we only had a few months to get the shack into a less distressed condition. There was no time to mess with Zed. I had the shack functioning at a first grade level in time to run off to China with Berk. CT moved all our junk and herself into the shack while I was gone. A more resilient wife you will never find.

Tinfiny has required massive amounts of sweat equity in the two years since we moved into the shack. In that time I walked Zed through New Mexico’s lost title maze and managed to get a shiny new title for a little over 150 dollars. Now the bike was mine: body and soul.

Having a title changed my relationship to Zed for the better. What was once a parts bike to be broken down and sold on the internet became a real motorcycle. I looked at the bike with a new appreciation for the classic lines and meaty, overhanging engine. The bike has stance. It is easy on the eyes with no hard edges or inorganic folds. It is a beautiful industrial product that has transcended the commercial realm and now resides in the empire of art.

Yeah, I’m gonna fix it, but not a restoration, that’s for people who can’t accept a missing eye on an old teddy bear. Life leaves scars. This will be a repair, a salvage operation to get Zed back on the road. I don’t know how long it will take but I know now is the time to start. At this point in my life I’m in no rush and it looks like Zed isn’t going anywhere either.

The Munro Doctrine

Way south-er than you’ve ever been, on the south end of the south island of New Zealand, there lived a motorcyclist named Burt Munro. For a country with a total population less than half of the Los Angeles basin, New Zealanders have an uncanny habit of punching far above their weight (see: rugby, wool). Burt Munro was no different. A pre-digital version of John Britten, he singlehandedly modified an ancient Indian motorcycle into a Bonneville land-speed-record holder. Sir Anthony Hopkins played Burt in the movie, The World’s Fastest Indian. That movie, combined with Polaris industry’s Burt-centric re-launch of the frequently-owned Indian motorcycle brand, means that it’s all Burt Munro, all the time.

In Burt’s hometown of Invercargill the Antarctic Circumpolar gyre swirls offshore. Mottled clouds streak across the sky. Conditions are changeable, the near-earth climate oscillates between cold rain, hail and bright sunshine (sometimes all three at once). Strong westerly winds sweep November’s clean air over and around the stunted mountains of the Southland. It’s springtime in the southern hemisphere, movement is everywhere and Invercargill is holding a motorcycle rally: The Burt Munro Challenge.

Kiwis are nothing if not low-key. At Challenge headquarters, directly off Dunns Road, there’s no trinket vendor-crush, no motorcycle manufacturer reps touting their recent parts juggling as new models and no Hard-Men dragging motorcycle trailers behind giant RVs. Two circus-sized tents, one for rally food, one for rally bands dominate the large, grassy field adjacent to Teretonga Park road course and Oreti Park Speedway.

Bold-colored dome tents and maybe a thousand motorcycles huddle along the tree line to the west. Co-ed shower buildings are situated on the north-east corner near the registration tent. Reflecting the gender makeup of the rally participants, women have access to the shower one hour a day. Plenty of Rent-a-Stink plastic johns are scattered about the field. At the center of all this is a large, round, water tank with a single faucet attached. Beneath the faucet is a stainless-steel sink, which drains into one of the long, shallow trenches crossing the rally grounds.

A half-mile away, on Oreti Beach, huddled between tufts of tall grass on the dunes I’m sitting in a direct line with history. This beach is where Burt Munro conducted speed trials in the foggy mists of time. Today, competitors are riding everything down the long, smooth sand. Rudges run alongside Yamahas, Sportsters writhe, a man with one arm and one leg saws his handle bar through the churned corners. The wind freshens to a gale, the ocean creeps onto the sand. As the tide rises, the oval track narrows until orange cones and inches separate the two straights. Nobody backs off. Sand and salt spray blast into the dunes scouring spectator’s eye sockets and cameras. You’ve got to really like motorcycles to be here.

The sun is going down and they’re still racing on the beach but I’m walking back to Challenge HQ. Man, it’s windy. The circus tents are surging and buckling. Large sections tear loose and crackle but the cafeteria-style food is hot and fine. “Fill your plate, Love.” I do.

Inside the heaving white marquee the temperature drops into the 40s. The wind grows stronger. Green and blue dome tents uproot their pegs and salute the field. Even the bobble-drunk biker stumbling around is curtailing his harassment of diners in order to pay attention to The Roaring Forties. Of course, I’d stick it out but my wife books a hotel room tonight.

In the morning it’s chilly and overcast. The rain starts as soon as I arrive at Teretonga Park for the Burt Munro Challenge road race series. I don’t remove my rain gear and won’t for the remainder of the day. There’s a little drinks trailer parked to the left of the control tower. I need hot coffee, stat.

“I’ll make coffee if you can geet that generator started.” The chick inside the trailer points to a rusted, 3500 watt Yamaha standing in a puddle of rainwater. Frayed battery cables protrude from the side of the generator. “Do you have a battery?”

“It don’t need one, you jist pull the rope.” The key is broken off in the ignition switch. I start to fiddle with the switch, “Don’t miss with that, Love. It stays like that all the time.” The rain gains strength; I give a few exploratory tugs on the rope, pretty good compression. “Where’s the choke?”

She’s getting frustrated, “I don’t think it his a choke, jist pull the rope!” I pull the rope. Nothing, not a pop or sputter. Rainwater dribbles down the blue tank onto the alternator’s oxidized lamination stack. “Does it have gas?” I gasp, eyeglasses fogged by body-steam rising from my plastic suit. “Yis, I think so. It was running fine then it jist quit. It’s normally no trouble at all.” Hail begins to fall.

There’s an opportunity to cross the track. Track stewards open the barriers and the pack of motorcyclists sheltering in the lee of an ambulance sprint to their bikes. If you miss it, several hours go by until you can cross again. “I got to go, maybe when it dries out it will start.” The coffee chick looks at the generator then to the dark sky. “Check the oil too. Some of these have a low oil shutdown.” I run back to my bike and with ice bouncing all around, cross into the infield.

Burt Munro races run rain or shine. This close to the Antarctic there’re no do-overs. Spectators for the pavement stuff are sparse but entrants are plenty. Classes include several divisions each of modern motorcycles, Japanese vintage, vintage and supermotard. Heat races of each plus the finals makes for a full day of exposure. I’ve never felt so outside. Between downpours the sun shines and the wind blasts. Tire selection is critical: the track surface in a single lap can vary from damp to submerged.

They’re breaking for lunch. Two paved sections of road run through the infield, I’m guessing for different track configurations. Along one section food stalls are doing a brisk trade. A guy in a sleek, stainless steel trailer has bratwurst for $8. Bread is $2 extra. There’s a coffee chick selling $4.50 long blacks out of the back of a mini van. Further down, two old ladies and a husky young girl huddle under a canvas gazebo. Rain is blowing in on the paper towels, a bowl of chopped onions slowly fills with rainwater.

Extension cords run across the wet grass then under the tent. One cord has a splitter feeding three food-warming cases. “What are these?” I point to the severed arm of a baby set amidst a quantity of unidentifiable foodstuffs. Lady one; “Those are hot dogs, Love.” I open the glass door, remove the steaming object and hold the flakey crust up to the bored-looking girl. “What’s the stuff in the middle?” I ask. As she studies the object her lip curls in disgust then she asks, “What are these again, mum?” Mum says with a resigned sigh, “Lamb. You know they’re lamb, Love.” I should have known. In New Zealand even their salads are made from lamb.

We are racing again. Under a corrugated lean-to jutting out from a building marked “Office” I nurse the $2, toasted baby-arm. The rain has gotten stronger again. There’re so many races I’m losing track of which class is running and who is leading whom. One guy is out there wearing a translucent plastic rain poncho. Each time he passes my spot the poncho disintegrates by degrees. There he is again, a translucent bib fluttering around his neck.

Burt Munro puts on an entire racing season in a single day. Some of the guys seem like they’re parading, no sense in wrecking your bike on such a snotty day. When a brief sunny spell interrupts the rain, I run over and grab a couple bucks worth of baby-arm. They race until after 5:00 p.m., meaning I must supplement dinner before the next event.

At Oreti Park speedway, the heat races start shortly after the Teretonga road races finishe. Oreti, a small dirt oval, contains The Burt’s best racing. Fast, handle-bar tangling and over quickly, the 4-lap heats are do-or-die. Sidecars, constructed with their wheels already leaned to the inside of the track, run clockwise: opposite the direction of the motorcycles but not simultaneously. By alternating the circulation pattern, management ensures spectators crowding the barriers will receive an even coat of sticky dirt. Nine hours of racing and I’m quitting. Battered by the wind and cold rain I reluctantly leave another racetrack with unfinished business. Burt would not be happy.

Motorcycles fill Dee Street in front of E.B. White’s hardware store. More motorcycles spill down the side streets. This is the final resting place of Burt’s offerings to the God of Speed. Over here is his record setting streamliner or maybe not: Burt’s liner was a work in progress, he messed with his Indian so much it’s hard to tell what is original. Add to that the existence of well-done movie-prop bikes, another original Munro Indian in The States, a one-lung-liner in a glass case that a local told me was The Real Bike, a bunch of fiberglass shells splashed from who knows what mold and the situation becomes a tad vague.

On a molecular level, everything is an original, even knock-offs churned out on an automated assembly line. This senseless quest for The Real Bike is a mug’s game and I’m not playing. All you need to know is that E.B. White’s is a fully functioning hardware store set within a classic motorcycle museum and you should go there once in your life.

It’s cold this morning but there’s no rain forecast. Motorcyclists straggle across the road from Challenge central. Ninety or so bikes have managed to make muster and at 9:30 a.m. we fire up for the Christmas toy run to Windham. Police block the intersections for us and within minutes we are in the rolling hills east of Invercargill.

Halfway to Windham, in the middle of nowhere, a VFR rolls to a stop. “What’s the problem?” The rider opens his gas cap and shakes the motorcycle back and forth, “I seem to be out of petrol.” Several other motorcyclists pull up to help. “Out of petrol? You can’t be serious, mate!” The jibes become more pointed. Luckily the sweep van stops and has a gallon of gas on board, sparing That Guy from any more abuse.

Windham is our final stop for The Challenge. The main streets of Windham are barricaded forming an intimate course. Another full slate of racing covering many, many classes is on tap. By golly, you get your money’s worth when you register for this rally. I try explaining to my wife how a 2013 motard differs from a 1937 Velocette, hence the many divisions but she sees only motorcycles.

The three-day, Burt Munro rally ends with a sigh. Some moto-pilgrims left before the Windham races, the others are dispersing by ones and twos throughout today’s final track sessions. Stealing a jump on real life, I guess. It’s been a great event, a real gathering of motorcyclists and one worth traveling halfway around the world to attend. The road east looks good and today’s fair weather is holding. We join the melancholy exodus. Out of town, we turn onto the quiet, post-rally highway and twist the throttle to the stop, traveling considerably slower than Mr. Munro.

Dream Bike: 1969 Kawasaki 500cc Triple

The 1969 Kawasaki 500cc Triple.

The ’69 Kawasaki Mach III 500cc two-stroke triple:  Wow!  It was a watershed wunderbike back in the days when the Big Four had serious engineering, the kind that went way beyond Bold New Graphics.  They were trying all kinds of mechanically wild and wonderful things then.  It was a magnificent time to start a motorcycle riding career.

Nicknamed the Widowmaker for its tendency to wobble and wheelie,  the Mach III was the fastest motorcycle of its era, its MSRP was under $1000, and it would whomp a Honda CB750 in a drag race.  I know because I was there.  I had a Honda 750 and my college compadre Keith had the Kawi triple.  I had a 50% displacement advantage and that extra cylinder, but it was to no avail. Keith cleaned my clock at every light.

Good buddy Gobi Gresh is all gaga on these bikes, so I guess that’s what induced my heightened sensitivity to the topic of all things two-stroke triple.  Yesterday morning a note arrived in my email from Motorcycle Classics (the gold standard of motorcycle magazines, in my opinion), and it mentioned an article on a Mach III restoration by Anders Carlson.  I sent it on to Arjiu knowing his perverted puttster predilections, he told me the story was really good, and I read it.  I agree.  I’ve never met Mr. Carlson, but let me tell you, the man can write.

Truth be told, I never wanted a Kawasaki Triple back then in any of the four flavors (I believe that as the line grew, they offered a 250, a 350, the original 500, and a 750 version).  Now, maybe having one would be cool.  I’d be a better man, I think, if I owned one.

I did my first international motorcycle ride ever with good buddy Keith back in the early ’70s.  Keith rode his ferociously fast 500 triple and I rode my Honda 4 from central Jersey to Montreal.  We were in high spirits, as might be expected.   We were two young guys riding our bikes to Canada.  Canada!  It would almost be like going to another country!  We were in engineering school back then, both of us were in Army ROTC, and it was a fun ride.  We joked that folks might think we were draft dodgers, heading to Canada and all.

We swapped bikes for a while somewhere in Vermont and I thought the Kawasaki was downright painful.  That bike could have been an enhanced interrogation tool before the term was invented. It felt like sitting a two-by-four plank.  The 500 triple was fast in a digital sort of way (full on, or full off) and I didn’t care for it.  My CB750 was a much more comfortable bike and it sounded the way I thought a motorcycle ought to.   You know, like an Offenhauser.  The Kawi sounded like a chain saw.

My buddy Peter had one of the Kawasaki 750 triples.  I didn’t know him then, but he told me a story about that bike going into a high speed wobble coming down California’s Cajon Pass (the result being one pitched Peter with a broken shoulder that bothers him to this day).   “I can’t tell you how many times I ran out of gas on that thing,” was his only other comment.  I guess it liked fuel.

Still, the Kawi two-stroke triples are iconic bikes, and the Carlson article I mentioned above is a great read.  If I was going to have a Kawi triple, it would be a white one with blue stripes (the original colors), just like Keith’s and the one you see in the photo above.

Wild Conjecture: The Demise of Kawasaki’s KLR650

Rumors are circulating on the Internet that Kawasaki is finally ceasing production of their KLR650 dual-sport motorcycle. Wild Conjecture has no clue if this is true but uninformed rumors are close enough for us.

Created shortly after the discovery of lead, and mostly made from the stuff, The KLR 650 has been a somewhat reliable off-road partner for generations of thrifty, vinyl-pocket-protector wearing goofballs. Easily crashed yet hard to pick up, the KLR has spawned a huge aftermarket of widgets and freeze-dried gooseberries to remedy the built-in defects that Kawasaki never had time to address during the bike’s short, 437-year production run. Oval pistoned long before Honda claimed to invent it, the KLR suffered from excessive oil use, bad doohickeys, wonky thing-a-ma-bobs, and who’s on first anyway?

As a KLR owner I’ll be sad to see the “Killer” letter designation dropped. Given the history of the 650 maybe Kawasaki can use the iconic KLR combination on a rail-transported pipeline trencher or large bulk oil carrier.

What’s done is done, where does Kawasaki go from here? Wild Conjecture has it on good authority that Mama K is modernizing their big dual sport with a new model designated the 1M-BC. Extensive use of wood and stone will lighten the 1M-BC and chain tensioner issues will be forever solved with a Kawasaki-exclusive “shoe leather” drive system.

My source claims the new 1M-BC will prove it’s woodle by participating in the not-so-demanding Pike’s Peak Downhill Time Trial, a race the bike has a fair chance of winning as no one else is aware of the race and Kawasaki is keeping the event date close to its vest.

Whatever Kawasaki comes up with to replace the KLR650 you can be sure Honda and Suzuki will be watching the result closely. Those two guys have more than paid off the tooling and engineering costs on their 650cc offerings. Who knows (not us!), maybe Kawasaki’s KLR-delete will prompt a renewal of factory interest in the moribund 650 Enduro class?


Wow, more Dream Bikes?  You bet!  Just click here!

The 2018 Motorado Show

The Motorado vintage motorcycle show is held once a year on the eastern outskirts of Santa Fe, New Mexico. It’s a cozy show with a few hundred entries and the parking lot contains a few dozen more worthwhile bikes. I could go into one of my patented off-topic rambles only to bring you back to the show 500 words from now but I’ll spare you the agony. Here are a few of the motorcycles I found notable.

This year’s Motorado was Italian themed and the round-case 750’s came out in force. These are beautiful bikes but the non-desmo, spring-valve GT850 with its bizarre, Jetsons styling is the one for me.

Adjustable rear dampers on the mono-shockish Moto Guzzi Falcone. Also known as the Baloney Slicer for the large outside flywheel. The Falcone sports a 500cc lay down engine and were used extensively by the Italian army and Police force.

Italian-themed doesn’t mean Italian only. Motorado hosts all brands and style motorcycle. This Series C Vincent was blinding in the clear blue skies of New Mexico. Spotlessly restored and British, no one puts this baby in a corner.

In all ways unfortunate, this ’73 Norton High Rider was one of the first-ever factory chopper style motorcycles. Someone at Norton spent a lot of time screwing up a great motorcycle. I can’t imagine how they decided enough was enough but it looks like they just stopped styling on the bike and called it good.

Pre-unit vs. Unit Triumphs: Me being me, I prefer the pre-unit engines for their added complexity and abundant opportunities to leak. The long primary cover looks better too. Unit Triumph lovers are soulless automatons who should never be invited to parties.

The rare Bridgestone GTR350. Disc-valved, two cylinders, this bike was a screamer. Motorado had an unrestored example on display. The owner says he has about 100 motorcycles in his collection! The aluminum crossover intake ducting has only a screen to keep debris out of the engine so I’m guessing these things wore out fairly fast.

A couple of Ravens utilizing Moto Guzzi engines as they were never intended. The twin-cylinder model is shocking enough but the single with its rear cylinder blanked off takes the prize.

My internet buddy Wes dropped by on his H2 with bits and pieces from many years and even some 650 Kawasaki wheels. The whole of the parts exceeds the sum of the parts in this case. It’s a sweet bike and I should have killed him and stolen the thing.

I have about a million more shots from the show but you get the idea. Keep the date open for Motorado 2019 and I’ll see you there, maybe on an old Z1 if I can get the beast going in time.


More Joe Gresh stuff is right here!

Named, noted, and quoted…

A comparo…Slick and Zero. It was fun doing this one.

Hey, this is cool.  Our story on the CSC City Slicker and Zero electric motorcycles was picked up (and quoted extensively) by a website called Electrek, an Internet magazine focused on electric vehicles.   Imagine that…being quoted in a magazine.   That’s cool…other people quoting me.  I’m working on learning how to write gud (spelling and grammar mistakes intended, folks) because when I grow up I want to write as well as Arjiu (and that would be my good buddy and literary hero, Joe Gresh).

Okay, enough on that.   I said I would someday explain the Dajiu and Arjiu business, and this is that day.

Dajiu and Arjiu in China. Yeah, we like gladiator movies…

So I’m Dajiu (which means big uncle, I’m told) and Joe Gresh is Arjiu (which means little uncle).  Our Chinese buddies gave us those names on the Western America Adventure Ride (you can read about that in 5000 Miles at 8000 RPM).   Joe and I were leading a ride around the western US with a group of guys from China, and they were having difficulty with both of us having the same first name.  It’s funny…most of the Chinese guys had adopted English names (Hugo, Leonard, Kyle, etc.) to make it easier for us, but they were having trouble with us having the same English name (Joe and Joe).  On the second day of that ride, Hugo (Zongshen’s factory guy) fixed it by giving us new names, Dajiu and Arjiu.  Hugo called us all together to make a formal announcement, and he handled it in a very solemn manner.   I imagine the ceremony was similar to becoming a made man in the Mafia, or maybe a Bar Mitzvah.  The Chinese guys thought it was marvelous.

The pronunciation is “Dah Geo” and “Ar Jeo” and our new Chinese names stuck.  Whenever we’re with the Chinese guys, they simply refer to us as Dajiu and Arjiu, as if those were our given names.  That’s how we’re introduced to others in China.  It’s pretty cool.  You can call us that, too, if you wish.

Wild Conjecture: The FTR1200 Indian

This photo may or may not be the new Indian FTR1200 that we’ve all been fantasizing about since Indian shoved both H-D and Kawasaki aside and took over flat track racing in America. Posted by Roger Gutterridge and brought to my attention by my internet buddy, Skip Duke, I have no way of knowing if this is the real thing.

Here at Wild Conjecture we don’t concern ourselves with facts. Indeed the very name of the joint suggests half-cocked ideas and squishy logic. But there are a few things that make me think this bike may be real.

What do you think?
A great engine.

The engine seems to be based on the regular Scout, at least the bottom-end looks mostly the same. I really don’t see why Indian would try to street-ify a race engine when the Scout unit is reliable and makes decent horsepower. What would be the advantage of creating another dealer parts stream and the exposure to warranty claims for a new engine that cuts a few pounds? The American motorcyclist has proven time and time again that weight is not a deal killer.

The frame looks pretty cool, perhaps a Ducati employee was spirited away to Spirit Lake? Rear suspension has Indian’s patented no-stroke shock absorber technology and by the girth of the spring looks to be mono shock. Front suspension is via the now traditional upside down fork with a steepish rake compared to Indian’s cruiser offerings. Flat track style handlebars top the front end. The front brakes are huge and doubled. Stopping should not be an issue with this bike.

Giant mufflers occupy most of the left rear section but I’m guessing there’s a box underneath to soak up more life saving noise. Body-wise, the gas tank could be a bit further forward and an inch or so higher in the front. As is it sort of looks like someone put the wrong tank on the FTR. I only have this one angle so it may be fine from another angle. The wheels look like they came directly off the race bike but I’m guessing in 17-inch for a wide selection of tires. Shod with flat track treaded tires, they look the business.

Nothing on the pictured bike looks undoable. Indian could start cranking these things out any time they wanted to. Overall, I like the bike. Since Indian began teasing us with hints of the street-going FTR about 482 years ago I’ve heard many comments from the buying public. The general consensus is that if Indian builds a street version of their 750cc race bike we will beat a path to their door.

This doesn’t look like a street version of Indian’s 750cc racer. It looks like a race styled version of their Scout. For real life street riding the Scout engine is the better choice and you won’t miss changing flywheels for an afternoon ride in the mountains. If you really want to race flat track just pony up the $50K and get the real thing.

Wild Conjecture loves the thing pictured even if it’s a red herring. More importantly, what do you think? Has Indian made the flat track bike that you said you would buy? Is this thing a phony? Is it real enough?


Check out all of our Dream Bikes here!